Shop AR Receivers Combo Receiver Sets
Combo Receiver Sets

UHP-15 Builder Set — Woodland Camo Cerakote

EARLY BLACK FRIDAY · 5% off$875.00 $831.25
Ships UPS flat rate $20.99Ships UPS to your dealer; faster UPS options at checkout.

Three CMT parts Cerakoted together in Woodland Camo: GEN 3 UHP-15 billet lower, UPUR-1 billet upper and HDM 15.0 Rail. Ships to your FFL.

This builder set is three CMT parts Cerakoted together in Woodland Camo: the GEN 3 UHP-15 billet lower receiver, the UPUR-1 billet upper receiver and the HDM 15.0 M-LOK rail with its barrel nut. Because it includes a serialized lower, the whole set ships to your FFL for transfer.

Ships to your FFL. This is a serialized receiver. At checkout you'll enter the receiving dealer's FFL, and we ship to them after the license is confirmed.

Limit 2 per order.

Install guide. Gen 3 UHP15 and UPUR-1 assembly notes: standard AR-15 lower parts kit, the pre-installed bolt catch pin and tensioning screw, barrel nut 70 ft-lb at most.
In stock
My cart

Part no. CMT-UHP15-BUILDER-WDL

Build it out

What goes with this builder set.

The rail is in the box. Add our nitrided M16 bolt carrier group and the upper is a barrel away from complete.

One finish across three CMT parts. This builder set pairs the GEN 3 UHP-15 billet lower receiver with the UPUR-1 billet upper receiver and the HDM 15.0 Rail, all Cerakoted in Woodland Camo.

Shout out to Pro 2 Customs for doing an awesome job on this Cerakote!

In the set

  • GEN 3 UHP-15 billet lower receiver
  • UPUR-1 billet upper receiver
  • HDM 15.0 Rail with its CMT barrel nut and clamp hardware

GEN 3 UHP-15 billet lower receiver

The GEN 3 UHP-15 is cut from 7075-T6 billet aluminum on CMT's own machines. The magazine well is machined to a flared, consistent profile that drops a mil-spec magazine cleanly, and the receiver extension threads and pin holes are held to spec so a standard lower parts kit and buffer assembly fit without lapping.

  • 7075-T6 billet aluminum
  • Flared, broached magazine well
  • Standard right-hand controls
  • Accepts a standard mil-spec lower parts kit and buffer assembly

UPUR-1 billet upper receiver

The UPUR-1 is machined from 7075-T6 billet aluminum. The barrel extension bore and the receiver face are cut in the same setup, so the barrel seats square and the extension indexes without the witness-mark guesswork that comes with a receiver machined in two operations.

  • Forward assist boss machined
  • Ejection port cover pin bosses machined
  • Standard right-hand eject
  • Flat-top MIL-STD-1913 rail, T-marked

HDM 15.0 Rail

The HDM 15.0 Rail is a free-float HDM handguard machined from 6061 extruded aluminum. It carries a continuous MIL-STD-1913 top rail that indexes flush with the flat-top upper, and M-LOK on every flat below the top rail.

CMT's barrel nut does not have to be timed. There is no shim stack to chase and no clocking the nut to clear the gas tube: torque the nut, slide the rail on, and clamp it.

  • Intended for a 16–18 in. barrel running a mid-length or rifle-length gas system
  • Clears low-profile gas blocks up to .750 in. journal diameter
  • Will not clear a standard A2 front sight base or a clamp-on gas block with an oversized body

What is not included. A builder set is a foundation, not a rifle. You still need a barrel, a gas block and tube, a bolt carrier group, a charging handle, upper and lower parts kits, and a stock or brace assembly to finish the build.

Installation. Fit and torque the barrel nut to the value in the instructions with the upper in a proper vise block and reaction rod. Confirm the gas tube passes through the nut without contact before clamping the rail. If you are not equipped to torque a barrel nut, have a qualified gunsmith install it.

This is a serialized firearm receiver. The whole set ships to a licensed dealer for transfer, not to your door. You must be 21 or older. Give us your dealer's information at checkout, or we will ask for it before the order ships.

PlatformAR-15
Part typeBuilder set, three pieces
SerializedYes — the whole set ships to a licensed dealer
Top railContinuous MIL-STD-1913
Barrel nutCMT proprietary — no timing, no shims
Barrel length16–18 in.
Gas systemMid-length or rifle
Gas block clearanceLow-profile, up to .750 in.
Magazine wellFlared, broached, mil-spec magazines
ControlsStandard right-hand
Forward assistYes
Ejection port coverProvision machined
Material7075-T6 billet aluminum receivers, 6061 extruded aluminum rail
FinishCerakote, Woodland Camo
OriginMachined in Tennessee, USA
LowerGEN 3 UHP-15 billet, stripped
UpperUPUR-1 billet, stripped
HandguardHDM 15.0 Rail, M-LOK

Questions about this part

What is in the Woodland Camo UHP-15 builder set?

Three parts: the GEN 3 UHP-15 billet lower receiver, the UPUR-1 billet upper receiver, and the HDM 15.0 Rail with its CMT barrel nut and clamp hardware. All three are Cerakoted in Woodland Camo. Barrel, gas block, bolt carrier group, parts kits and stock are not included.

Does the builder set have to ship to an FFL?

Yes. The set includes a serialized lower receiver, so the whole set ships to a licensed dealer for transfer, the same as a CMT lower bought on its own. Enter your dealer at checkout. The limit is two sets per order.

What barrel and gas system suit the 15 in. rail in this set?

The HDM 15.0 Rail is intended for a 16 to 18 in. barrel on a mid-length or rifle-length gas system, and clears low-profile gas blocks up to a .750 in. journal. It will not clear an A2 front sight base.

Who did the Cerakote on this builder set?

Pro 2 Customs (pro2customs.com) applied the Cerakote finish on these builds. The receivers and rail are machined by CMT in Tennessee.

Customer experience

Reviews

— ☆☆☆☆☆ Loading reviews…
Loading reviews…

Write a review

If you bought this part from us, your review publishes straight away. Otherwise we read it first. Your email address is never shown.